Microe CET for MTE Series Uživatelský manuál

Page 1Compact Encoder Tape (CET™) Scale Installationfor MTE Series EncodersInstallation Manualand Reference GuideMicroE Systems • 125 Middlesex Turnpi

Page 10CET™ Scale, MTE Top/Side Mount ConfigurationsInstallation By Hand 4.Place the CET™ Tape Scale against the mounting surface “D” reference edge.

Page 11CET™ Scale, MTE Top/Side Mount ConfigurationsInstallation By Hand 5.Install the CET Scale along the remaining length of the mounting surface.Pr

Page 12CET™ Scale, MTE Top/Side Mount ConfigurationsInstallation By Hand 6.Once the scale is applied to the mounting surface, and before the blue prot

Page 13Applicator tool spring loaded contactcylinder Up/Down position knobCET scale entrychannelSpring loaded contact cylinder1.Overview of CET Scale

Page 14CET™ Scale, MTE Top Mount ConfigurationInstallation By Mounted Applicator Tool The correct end of the tape to insert is shownbelow.5.Applicator

Page 15CET™ Scale, MTE Top Mount ConfigurationInstallation By Mounted Applicator Tool Peel back about 50mm (2 inches) of clear adhesive backer tape.8.

Page 16CET™ Scale, MTE Top Mount ConfigurationInstallation By Mounted Applicator Tool 9.Tape Scale InsertionPush the scale slowly into the Applicator

Page 17CET™ Scale, MTE Top Mount ConfigurationInstallation By Mounted Applicator Tool 11.Apply the Tape ScalePush the Applicator Tool and fixture asse

Page 18CET™ Scale, MTE Top Mount ConfigurationInstallation By Mounted Applicator Tool 12.Once the scale is applied to the mounting surface, and before

AABDPage 19CET™ Scale, MTE Side Mount ConfigurationInstallation By Mounted Applicator Tool 1.MTE Side Mount Tape Scale Applicator Tool (Model Number:

Page 2Table of ContentsCompact Encoder Tape (CET™) Scale InstallationIntroductionIntroduction (Precautions, Patents, Manual Revisions) ...

Page 20CET™ Scale, MTE Side Mount ConfigurationInstallation By Mounted Applicator Tool 3.Mount the Applicator Tool.Mount the Applicator Tool in the Si

Page 21CET™ Scale, MTE Side Mount ConfigurationInstallation By Mounted Applicator Tool 5.Peel off a short section of bottom adhesive backing approxima

Page 22CET™ Scale, MTE Side Mount ConfigurationInstallation By Mounted Applicator Tool 7.Insert a short section of tape scale into the tool, approxima

Page 23CET™ Scale, MTE Side Mount ConfigurationInstallation By Mounted Applicator Tool 9.Move the tool in a steady motion to apply the tape scale.Push

Page 24CET™ Scale, MTE Side Mount ConfigurationInstallation By Mounted Applicator Tool NOTE: After removing the blue protective film, the scale is rea

Page 25End Cap Installation for CET™ ScalesOptional1.Epoxy Setup• Mix the two-part epoxy and place it in a syringe or on the end of a stick. Do not us

Page 26Final Cleaning, Inspection and Cure TimeBefore using the encoder for servo control, clean the tape scale using alcohol or acetone and a lint-fr

Page 27Contacting MicroEMicroE Systems is a world leader in optical encoder technology withoffices in major industrial centers around the globe.To lea

Page 3PrecautionsFollow standard ESD precautions. Turn power off before connecting the sensor. Donot touch the electrical pins without static protecti

Page 4OverviewThis manual applies to the installation of the following scale types.• PurePrecision Compact Encoder Tape (CET™) for MTE Series, Model C

Page 5Pre-Installation Information and PrecautionsRead all instructions completely before beginning theinstallation process.The CET™ Scale is a precis

Page 6Design Guidelines1.Verify the tolerances of the scale's mounting surface given in the Interface Drawing.2.Verify the dimensions of the scal

Page 7Mounting Surface Preparation1.Inspect the mounting surface for any machining irregularities. MicroE Systems recommends a surface finishof better

Page 8Cutting the CET™ Scale 1.Uncoil the tape scale and cut it to the required length using shears.Note: check the interface drawing to makesure the

Page 9CET™ Scale, MTE Top/Side Mount ConfigurationsInstallation By Hand 2.Removing/peeling the bottomadhesive liner. CET Scales have 3 layers, blue pr